HULL CONSTRUCTION

Heavy duty GRP Moulding, hand laid to Northshore Nordseal laminating system incorporating multi-axial and unidirectional reinforcements. Thickness increases progressively towards the keel area. The keel box is an integral part of the hull lay-up and sandwich construction stiffening runs the entire length of the hull topsides. All main bulkheads are bonded into the hull at the main layup stage along with a stiffening grillage of transverse frames and longitudinal stringers. The engine bearers are also on integral part of the hull structure.

• Gelcoat colour: Ivory White 9010

• Boot top stripes: Oxford Blue

• Style lines: Oxford Blue

• Underwater finish: Clear gelcoat with Coppercoat treatment to hull and keel

 

DECK CONSTRUCTION

Hand laid GRP. Sandwich type construction using balsa core stiffening, with marine plywood in high stress areas where fittings are positioned. Heavily stressed areas are additionally reinforced with unidirectional glass reinforcement, The deck is bonded to the hull through the entire length and to all main bulkheads resulting in a strong an integrated unit. Teak cappings are used to cover the hull to deck joint upstand

• Gelcoat colour: Ivory White 9010

• Ring deck: Teak laid

​

VARIABLE DRAFT KEEL

The fixed ballast is an iron casting which acts as a grounding plate and as transverse stiffening for the keel unit. It is fitted into a recess in the hull in the area of the keel box with stainless steel bolts. The aerofoil swing keel is cast iron and incorporates a stainless steel pivot at the leading edge. The swing keel is raised and lowered by a hydraulic ram powered by an electrically driven pump with a manual back up. All hydraulics are easily accessible for maintenance. A keel control panel and gauge showing keel position is fitted at the wheel pedestal. A removeable stainless steel pin positioned to enable the keel to be locked in the “UP” position.

​

ENGINE

• Yanmar 4JH4-E 56hp 4 cylinder fresh water cooled diesel engine (Fully serviced Dec 2022)

• New engine panel and tacho fitted 2023
  Reduction/reverse gear

• Balmar high output alternator with external regulator and temperature sensors (New 2023)

• Bronze stern tube with water lubricated stern gland

• Stainless steel propeller shaft

• Bronze three bladed Max-Prop automatic feathering propeller

• Ambassador AM10 rope cutter fitted to shaft

• Substantial skeg fitted on centreline to protect propeller and rudders when yacht is dried out

• Non-metallic fuel tank under cabin sole below chart table – capacity 246 litres/54 gallons, with sediment trap and line filter

• Non-metallic water strainer with removeable filter

• 12V electric ventilator

• Sound deadening to engine box

• Hinge up panels at either end of engine box for access

• Engine box can be completely removed for maintenance.

• SeaFire automatic FG50A fire extinguisher fitted in engine compartment

​

THRUSTERS

• Lewmar 75Kg bow thruster with control mounted at steering position

• Lewmar 75Kg stern thruster with control mounted at steering position

​

ENGINEERING

• Diesel powered hot air system with five outlets, aft cabin, aft heads, saloon, forward heads and forward cabin

• Holding tank system fitted, one tank fitted under saloon, one tank fitted under sail locker, heads will pump to sea or into tank via diverter valves

​

ELECTRICS & ENGINEERING

• 12 Volt system

• Four heavy duty 130Ah AGM batteries charged from engine alternator, one for engine, three for domestic use

• Mastervolt Mass Combi unit 12/1200 -100 battery charger and inverter unit

• Mastervolt MICC control panel for Mass Combi with battery monitor and shunt

• Isolating switches

• Cabin lighting throughout

• Reading lights over bunks

• Chart light over navigation table

• Full LED navigation light system, incorporating bow light, stern light, masthead tricolour light with all round white anchor light, deck flood light and steaming light.

• Circuit breakers on main panel

• Three 12V interior sockets, cigarette lighter type, fitted at nav station

• 12v interior socket, cigarette lighter type, fitted starboard end of instrument pod

• 240v Ring main, with three double outlet sockets, earth leakage circuit breaker and shore power connection. with cable and plug
  12V 25amp socket fitted in cockpit locker (For high load such as dinghy inflator)

• Shaver sockets fitted in both heads
  Galvanic isolator

• 2 x Solara SM120M 34Wp solar panels with regulator fitted to forward coachroof

​

WATER SYSTEMS & PUMPS

• Pressurised hot and cold water system

• Mixer tap to galley sink

• Aquafilta to galley fresh water

• Mixer tap in heads compartments

• Two non-metallic water tank – Total Capacity 270 litres/59 gallons

• Electric pressure pump

• Hot water provided by engine calorifier unit

• Electric sump pumps to shower trays

• One manual bilge pump

• One electric submersible bilge pump

• Deck wash pump, with outlet in cockpit

• Deck shower with hot and cold water fitted on transom

• ​

NAVIGATION & ELECTRONICS

• Raymarine ST60+ speed depth and wind indicators mounted in teak instrument panel mounted above companionway hatch

• Airmar Ultrasonic speed transducer

• Raymarine ST60+ graphic display repeater mounted at portside helm position

• Raymarine ACU400 autopilot with Mamba drive.

• P70s autopilot displays mounted in cockpit at both helms and at chart table with EV1 sensor corepack and internal rate Gyro

• Raymarine smart controller wireless remote for autopilot

• Raymarine RAY218E VHF radio with DSC functions including aerial and external horn/speaker with Raymic 2nd hand station fitted in cockpit

• Raymarine AIS250 received for collision avoidance

• Sea-me active transponder radar reflector fitted at mast

• Raymarine Quantum radar scanner, with doppler, (New 2019) mounted on Scanstrut bracket at mast

• Two Raymarine Axiom Pro 12 high performance displays (New 2019) mounted in GRP Navpods with stainless steel cranked rail, mounted port and starboard helm positions

• Raymarine Raystar 125 GPS antenna mounted to pushpit

• Navtex 6 Plus for weather and navigation warnings

• 15” LCD monitor with Raymarine Seatalk 2 keyboard at Nav station to link with E80 plotters on deck

• Fish finder module for E80 display with Seatalk network switch

• Glomax TV antenna mounted at mast head

• Three zone audio system (Aft cabin, saloon and cockpit, with Sony speakers and iPod cradle.

• 17” Flat screen TV/DVD combi unit on swing retracting mounting aft fitted in saloon

​

STEERING

• Semi balanced twin rudders

• Twin 30” stainless steel cockpit wheels with hide cover to rims

• Lewmar/Whitlock Cobra steering system

• Single lever engine control

• Emergency steering system

• 6” main steering compass and compass guard

​​

SPARS & RIGGING

• Selden fractional rig

• Double swept back spreaders

• Selden anodised aluminium spars finished in silver (Mast & boom fittings serviced 2020) Double headsail rig with extra furling forestay forward to take Genoa

• Internal halyards

• Stainless steel wire standing rigging with swage toggle fork rigging screws (Replaced 2020)

• Backstay with manual tensioner (fully service 2020)

• Furlex reefing systems to forestays (Fully service 2020)

• Single line reefing led to aft cockpit for mainsail

• Kicker with strong gas insert (Replaced 2021)

• Kicker, jib sheet, main halyard, topping lift, outhaul and 2 reefs lead aft
  Jib halyard at mast

• Burgee and signal halyards

• Sail control lead aft across pilot house

• Lewmar 30 winch on mast

• Three part lazy jacks for slab reefing mainsail (new 2020)

• Removeable stainless steel bowsprit for gennaker

• Telescopic spinnaker pole with topping lift, mast crane, downhauls and vertical mast stowage

• Scott Boom Lock

​

SAILS

• North, grey Norlam Xi09 sails

• Furling, self tacking, jib with 3 vertical battens, NPL Tour Xi Grey Norlam (New 2016)

• Overlapping furling Genoa, NPL Tour Xi Grey Norlam (New 2016)

• Full batten mainsail, with 5 horizontal battens for slab reefing,

• NPL Tour Xi Grey Norlam (New 2016) Mainsail stack pack cover in Dune 5026 canvas

• Furling asymmetric G1 gennaker with Karver furling gear

​

​

​

COCKPIT

• Aft cockpit

• Self-draining

• Laid teak to cockpit seats and cockpit sole

• Cockpit table with folding leaves, stowage, and handrails

• Good access aft for boarding through transom

• Telescopic stern boarding ladder

• Cockpit locker to port and starboard

• Drained gas bottle stowage in cockpit locker to starboard

• Liferaft/fender stowage in cockpit locker to port

• Sliding acrylic companionway hatch with washboard

• Instrument panel above hatchway

• Two winch handle pockets

• Two safety harness eyes

• Covers for wheels and cockpit table in Dune 2056 canvas

• Sprayhood with stainless steel frame in Dune 5026 canvas

• Cockpit tent with stainless steel frame, with roll up sides and back, in Dune 5025 canvas

• Cockpit cushions, using drainable foam, to cover full cockpit seating area ​

​

DECK GEAR & LOOSE EQUIPMENT

• Cleats forward and aft raised

• Spring cleats amidships with stainless steel chafe guard

• Transom cleats fitted port and starboard

• Stainless steel stemhead fitting with twin bow roller

• GRP foredeck anchor locker for with reinforced shelf for anchor windlass

• Lewmar H2 electric windlass with hand held control switch

• Chain counter for windlass fitted at portside steering position

• Stainless steel pulpit incorporating navigation light bracket

• Stainless steel stanchions and guardwires, with gates port and starboard (Replaced 2020)

• Stainless steel pushpit incorporating stern gate, navigation light bracket and ensign socket

• Fuel and water deck fillers

• Self-tacking foresail track with sheet to cockpit

• Turning blocks to take reefing lines

• Mainsheet track with control lines

• Spinlock XCS power clutches on each side for running rigging

• Two Lewmar 46SAEST electric mainsheet winches

• Lewmar 44AEST electric halyard winch

• Two Lewmar 48AEST electric genoa winches

• Stainless steel grab handles on either side of the coachroof with integral mainsheet lead

• 16 Kg Delta anchor

• 50 Metres of calibrated 10mm chain

• 30 Metres of rope warp

• Two fire extinguishers

• One fire blanket

• Seven fenders and tails

• Five mooring warps

• Boat hook

• Ensign and staff

• Plastimo 6 man offshore standard pack cannister liferaft mounted in stainless steel liferaft bracket mounted to pushpit rail

• Teak pad for outboard engine stowage mounted to pushpit rail

• Outboard motor davit, Nova-Lift, fitted to pushpit

• 9.5kg Fortress kedge anchor, with chain and warp in bucket, with kedge guide roller on aft starboard deck

• Harness webbing jackstay port and starboard side decks (Replaced 2020)

​

​WINDOWS, HATCHES & VENTILATION

• Four size 22 opening deck hatch to saloon and forward cabin

• Two size 44 opening deck hatch to saloon and forward cabin

• Two size 00 opening hatches to galley and chart table

• Five opening ports in aft cabin

• Acrylic sliding companionway hatch

• Pilothouse windows and hull ports are tinted toughened glass bonded into recessed in the GRP mouldings

​

​INTERNAL JOINERY & UPHOLSTERY

• Internal joinery is finished in solid wood with faced marine quality plywood

• Linings are fabric covered plywood and GRP moulding as appropriate

• Cabin soles are teak striped non-slip laminates

• Joinery: American Cherry

• Galley worktop: Formica deep blue Ice S0811

• Heads worktop: Formica black lava S2649

• Saloon upholstery: Alcantara Blue 6801

• Navigation seat: Birch Navy

• Cabin upholstery, berths: Brooklyn 4014/03 Calico Aft cabin headboard: Alcanta Blue 6801

• Curtains, sleeping cabins: Fresco 16145 746

• Concertina blinds fitted to raised coachroof windows

​

ACCOMMODATION

The layout is in accordance with the general arrangement drawing. There are a total of six berths, with two in the forecabin. two in the aft cabin and two in the saloon.

​

GALLEY​

• Galley to port

• Stainless steel sink

• Hot and cold pressurised water

• Corian type worktop

• Stainless steel grab rail to worktop

• Top loading refrigerated ice box, 75 litres, with keel cooler to compressor unit

• Fully gimballed gas cooker with two burners, grill, and oven, with fail safe devices on all burners

• Sharp compact Microwave 240 volt

• Gas cut off tap

• Ample storage for crockery and cutlery

• Cupboards

• Two Opening hatches

• Overhead light

 

SALOON

• Full length “L shaped” single settee to port and full length settee to starboard Lee cloths for using settees for sleeping berths

• Folding leaf table

• Two lockers forward

• Shelves outboard

• Stowage under seating Large, shelved locker forward

• Overhead lights

 

NAVIGATION AREA

• Chart table to Starboard with excellent visibility

• Seat

• Instrument console forward of chart table

• Chart stowage under hinged lid

• Locker spaces

• Opening hatch

• Overhead light

• Chart light

• Main switch panel

​

FORE CABIN​

• V berth, two long single berth Infill to convert to a double

• Large hanging locker

• Two Full lengths shelves

• Two fixed portlights

• Opening deck hatch

• Overhead lights

• Two LED reading lights

• Curtains

 

FORWARD HEADS

• Marine toilet
  Washbasin with Corian type worktop

• Hot and cold pressurised water

• Grating to shower tray

• Electric shower waste pump

• Opening Hatch

• Fixed portlight

• Lockers

• Mirror

• Extractor fan/blower with 2 way switch

 

AFT CABIN

• Large centreline double berth

• Upholstered seats to port and starboard

• Two corner lockers

• Large hanging locker

• Shelves

• Three opening portlights

• Two fixed portlights

• Overhead light

• Two LED reading lights

 

AFT CABIN ENSUITE

• Marine toilet

• Washbasin with Corian type worktop

• Hot and cold pressurised water

• Electric shower waste pump

• Grating to shower tray

• Lockers

• Mirror

• Fixed portlight

• Opening portlight

• Extractor fan/blower with 2 way switch